Главная страница
Поиск по модели:
  
Модели кораблей чертежи скачать
Демо солнышко в руках слова
Как сделать шуруповерт от сети 220
Как получить временную регистрацию в минске
Где родился андрей черкасов
Детские кроватки своими руками из дерева чертежи
Структура момента 2017
Крымская область акмечинский район на карте
 

Model c 2002 radio control console инструкция - Инструкция по эксплуатации Ericsson RC-1215P

CT Desktop Display CT Thin Display CT Large Display CT Console Display CT Desktop Master Driver CT Large Master Driver CT Desktop GPS Driver CT Large GPS Driver CTManual Contents General Description Models Models All Display Models: Will accept serial Time-of-Day and timer data in Radio Systems format, or Time-of-Day only data in SMPTE format. To Set the Clock: If Serial Time of Day is supplied to the CT slave mode , it will not be possible to enter the Time-of-Day set mode.

Setting the time-of-day can either be done at the master unit or the displayed hours can be offset via the IR Remote Control. Provide serial data to the unit. Choices of serail data are SMPTE time code and Radio Systems Time-of-Day data from CT GPS or CT Master units. In addition a CT display unit can be used to provide Time-of-Day and Timer data in the Radio Systems format.

To connect to slave Time-of-Day displays only, wire only the serial data input terminals in parallel use either the terminal strip or RJ connectors — Provide serial data from any CT display unit whose timer display you want to slave. Connect the serial data output terminals of the up-stream CT Display to the serial data input terminals of the slave display.

Use either terminal strip or RJ connectivity consult wiring diagram on page Storing Down Times The IR Remote Control can be used to store up to six down times. These times are saved when power is removed from the CT Press the Timer Button.

The Timer Led will illuminate. Using the numeric keypad, enter a down time. The Set Led and Down Led will illuminate. The clock must be set when using the internal clock base. Time-of-Day set The CT will not enter the Time-of-Day set mode if serial time of day is being supplied by a master clock or GPS system.

However, the displayed time may be offset up to 23 hours, see IR Remote Setup Functions - page CT Manual Setup Functions The IR Remote Control is used to set various functions of the CT Press the Program Button.

Repeatedly press- ing the Setup Button will step the CT through the 10 menu choices. CT Manual Option six: Use the numeric keypad to enter the minutes and seconds of the time compare.

When the minutes and seconds of the time of day are equal to the time compare stored, the matching open collector wired remote will activate. Stored Down-Time 1 can be recalled pressed.

In addition, the CT will return remotely via parallel remote control wiring. CT Manual Master Driver Additional Operating Instructions For units equipped with the optional master driver board To Set the Time on clock power up 1. Clock will power up in the set mode at The display will be frozen. Units are shipped from the factory in the 12 hour mode. CT Manual Operation After all connections are made, apply power.

The unit will take from 1 to 15 minutes to acquire the satellite data. During this initial acquisition period, and during any subsequent periods of satellite data loss, the GPS Master unit will display one of 5 error codes. Up to 10 Radio Systems AC analog clocks can be directly connected to any CT Master or GPS driver board. If more than 10 clocks are to be utilized, they may be connected via the AMD-1 analog clock driver.

Analog clocks con- nected to the GPS Master driver will automatically be updated for Daylight Savings Time and Standard Time. Push the START button to resume normal digital clock operation. Adjustments made via the CT Master driver will effect any digital clocks downstream. On systems that utilize the AMD-1 analog clock driver, all time adjustments should be made via this unit.

Consult the AMD-1 manual for adjustment instructions. CT Manual Analog Clock Connections to CT GPS and Master Models Page CT Manual Serial Time of Day Connections from CT, GPS or Master Models Page Satellite Receiver Antenna Note: The cable used must be shielded with the ground connected to pin 1 on both ends.

CT GPS Driver II. CT Manual Connection Diagrams CT GPS Dip Switch Settings Page During the warranty period, there will be no charge for parts or service made to units which show no sign of misuse by customer or lightning caused damage. The customer is responsible for the cost of shipping their unit back to Radio Systems for repair.

Page of 28 Go. Download Table of Contents Contents Print This Page Print Share Share Url of this page: Radio Systems CT on manualslib. Also See for CT Manual - 28 pages Manual - 25 pages. CT Desktop Master Driver.

CT Large Master Driver. CT Desktop GPS Driver. CT Large GPS Driver. Was This Manual Helpful? YES NO Well done! Also See for Radio Systems CT Radio Systems CT Manual 28 pages. Radio Systems CT Manual 25 pages.

Radio Systems CT-2002 Manual

Related Manuals for Radio Systems CT No related manuals. Summary of Contents for Radio Systems CT Page 1 Radio Systems, Inc. Table Of Contents Radio Systems, Inc. Models, General Description Radio Systems, Inc. Page 7 Provide serial data to the unit. Wired Remote Control Provide serial data from any CT display unit whose timer display you want to slave. Up Timing, Down Timing, Storing Down Times Storing Down Times The IR Remote Control can be used to store up to six down times. Recalling Stored Down Times, On Power Up, Time-of-day Set The clock must be set when using the internal clock base.

Setup Functions CT Manual Setup Functions The IR Remote Control is used to set various functions of the CT Page 12 Radio Systems, Inc. Page 13 See page 7.

RADIO SYSTEMS CT MANUAL Pdf Download.

Additional Operating Instructions, Master Driver, To Set The Time on Clock Power Up , Battery Lamp Radio Systems, Inc. Hour Operation Radio Systems, Inc. Operation, Gps Error Codes Radio Systems, Inc. Initial Time-of-day Set Up to 10 Radio Systems AC analog clocks can be directly connected to any CT Master or GPS driver board.

Page 20 Radio Systems, Inc. Analog Clock Connections To Ct Gps And Master Models Radio Systems, Inc.

Radio ::Dispatch Products ::Desktop Consoles ::Bosch Telex ::C ::Airadio - Communication Solutions When It Matters

Serial Time-of-day Connections From Ct Gps Or Master Models Radio Systems, Inc. Serial Clock Timer Connections Between Ct Stand Alone Models Radio Systems, Inc. Page 24 Satellite Receiver Antenna Note: Page 25 Radio Systems, Inc. Warranty During the warranty period, there will be no charge for parts or service made to units which show no sign of misuse by customer or lightning caused damage. Page 28 For Assy. Comments to this Manuals Your Name. Enter text from picture: To print the manual completely, please, download it.

Got it, continue to print.



 
001776
В освоении новой техники Вы поступаете так:
изучаете инструкцию
просите кого-нибудь помочь
полагаетесь на интуицию
© 2005 — 2016 «xn----otbfdoaebgkp6a.xn--p1ai» Документы на все случаи!